Cjmm1 Series 2p/3p Moulded Case Circuit Breaker MCCB with IEC60947-2

Product Description

 

Product Description

Application
1.CJMM1 series moulded case circuit breaker(hereinafter referred to as circuit breaker) is pplicable for AC 50/60HZ power distribution network
circuit with rated insulation voltage of 800V, rated operation voltage of 690V and rated operation current from 10A to 630A, it's used to distribute power and prevent circuit and power supply equipment from damage due to overload, short circuit, under voltage and other faults, it's also used for infrequent start of motor as well as overload, short circuit and under voltage protection

2.This circuit breaker owns advantages of small volume, high breaking capacity, short arcing (or noarcing)etc, it can be equipped with accessories like alarm contact, shunt release, auxiliary contact etc, it's an ideal product for user.

3.The residual current circuit breaker can either be vertically installed (vertical installation) or be horizontally installed (horizontal installation)
The product is in accordance with the standards of IEC60947-2 and Gb140482

Classification
1.By breaking capacity: a standard type(type S) b higher breaking capacity type(type H)
2.By connection mode: a front board connection, b back board connection, c plugin type
3.By operation mode: a direct handle operation, b rotation handle operation,c electrical operation
4.By number of poles: 1P,2P, 3P, 4P
5.By accessory: alarm contact, auxiliary contact, shunt release, under voltage release.

Normal Service Condition
1.The altitude of the installation site shall not exceed 2000m
2.Ambient air temperature
a.The ambient air temperature shall not exceed +40ºC
b.The average value shall not exceed +35ºC with in 24 hours
c.The ambient air temperature shall not be less than-5ºC
3.Atmosphere condition
a.There lative humidity of atmosp here shall not exceed 50% at highest temperature of +40ºC,and it can be higher atalower temperature,when theaver agelowest temperature in the wettest month doesn't exceed 25ºC can be 90%,conden sationon product surfacedue to temperature change must be takenin to account.
4.The pollution level is class 3

Table1

Accessory name	Electronic release	Compound release
Auxiliary contact,under voltage release,alam contact	287	378
Two auxiliary contact sets,alarm contact	268	368
Shunt release, alarm contact, auxiliary contact	238	348
Under voltage release,alarm contact	248	338
Auxiliary contact alarm contact	228	328
Shunt release alarm contact	218	318
Auxiliary contact under-voltage release	270	370
Two auxiliary contact sets	260	360
Shunt release under-voltage release	250	350
Shunt release auxiliary contact	240	340
Under-voltage release	230	330
Auxiliary contact	220	320
Shunt release	210	310
Alarm contact	208	308
No accessory	200	300

Main Technical Parameter

1.Rated value of circuit breakers

Model	Imax(A)	Specifications(A)	Rated Operation Voltage(V)	Rated Insulation Voltage(V)	Icu(kA)	Ics(kA)	Number of Poles (P)	Arcing Distance(mm)
CJMM1-63S	63	6,10,16,20 25,32,40, 50,63	400	500	10*	5*	3	≤50
CJMM1-63H	63		400	500	15*	10*	3,4
CJMM1-100S	100	16,20,25,32 40,50,63, 80,100	690	800	35/15	22/5	3	≤50
CJMM1-100H	100		400	800	50	35	2,3,4
CJMM1-225S	225	100,125, 160,180, 200,225	690	800	35/15	25/5	3	≤50
CJMM1-225H	225		400	800	50	35	2,3,4
CJMM1-400S	400	225,250, 315,350, 400	690	800	50/15	35/8	3,4	≤100
CJMM1-400H	400		400	800	65	35	3
CJMM1-630S	630	400,500, 630	690	800	50/15	35/8	3,4	≤100
CJMM1-630H	630		400	800	65	45	3

Note: When the test parameters for the 400V, 6A without heating release

2.Inverse time breaking operation characteristic when each pole of overcurrent release for power distribution is powered on at the same time

Item of test Current (I/In)	Test time area	Initial state
Non-tripping current 1.05In	2h(n>63A),1h(n<63A)	Cold state
Tripping current 1.3In	2h(n>63A),1h(n<63A)	Proceed immediately after No.1 test

3.Inverse time breaking operation characteristic when each pole of overcurrent release for motor protection is powered on at the same time.

Setting Current Conventional time Initial State			Note
1.0In	>2h	Cold State
1.2In	≤2h	Proceeded immediately after the No.1 test
1.5In	≤4min	Cold State	10≤In≤225
	≤8min	Cold State	225≤In≤630
7.2In	4s≤T≤10s	Cold State	10≤In≤225
	6s≤T≤20s	Cold State	225≤In≤630

4.The instantaneous operation characteristic of circuit breaker for power distribution shall be set as 10in+20%, and the one of circuit breaker formotor protection shall be set as12ln±20%

Outline Installation Size

 

About Us

 

More products